{"id":11871,"date":"2026-06-20T21:00:00","date_gmt":"2026-06-20T19:00:00","guid":{"rendered":"https:\/\/rodervision.com\/unkategorisiert\/led-illumination-for-pcb-and-electronics-inspection-soldering-components-and-trace-verification\/"},"modified":"2026-05-25T17:35:23","modified_gmt":"2026-05-25T15:35:23","slug":"led-illumination-for-pcb-and-electronics-inspection-soldering-components-and-trace-verification","status":"publish","type":"post","link":"https:\/\/rodervision.com\/de\/anwendungen\/led-illumination-for-pcb-and-electronics-inspection-soldering-components-and-trace-verification\/","title":{"rendered":"LED Illumination for PCB and Electronics Inspection: Soldering, Components and Trace Verification"},"content":{"rendered":"\n

PCB and electronics inspection is among the most demanding applications in industrial machine vision. Component dimensions are shrinking with every product generation. Solder joints are often smaller than 0.5 mm. Gold-plated pads, tin-coated surfaces, and solder paste all have very different reflectance properties. An illumination approach that works for one task on a PCB may produce completely unusable images for another task on the same board.<\/p>\n\n

The illumination engineer must therefore treat PCB inspection as a multi-task problem. Different inspection tasks require different illumination geometries, often on the same board in the same production line. Understanding the optical characteristics of each inspection target is the starting point for designing an effective illumination strategy.<\/p>\n\n

The PCB Inspection Challenge: Miniaturisation and Reflective Surfaces<\/h2>\n\n

Modern PCBs combine multiple surface types in a very small area. Bare FR4 substrate, solder mask, solder paste, solder joints, copper traces, gold-plated pads, component bodies, component markings, and adhesive dots may all be present within a few square centimetres. Each material has a different reflectance, colour, and surface texture. Each responds differently to direct, diffuse, coaxial, and darkfield illumination.<\/p>\n\n

The trend toward miniaturisation makes the problem more severe. As component packages shrink from QFP to BGA to CSP, the spatial resolution requirement of the inspection system increases. Higher magnification means smaller field of view, which in turn means that the illuminator must deliver consistent intensity and uniformity over a smaller area while maintaining the correct geometry for the inspection task.<\/p>\n\n

<\/div>\n\n
\"\"<\/span>
\n

M\u00f6chten Sie Hilfe bei der Auswahl des Produkts?<\/strong><\/p>\n\n\n\n

\n
Klicken Sie hier!<\/a><\/div>\n<\/div>\n<\/div><\/div>\n\n
<\/div>\n\n

Solder Joint Inspection: Coaxial and Dark-Field Illumination<\/h2>\n\n

Solder joint inspection is the most critical task in SMT assembly quality control. The goal is to detect insufficient solder, excess solder, solder bridges, cold joints, and tombstoning. Each defect type has a different three-dimensional form and a different optical signature.<\/p>\n\n

Coaxial Illumination for Flat Solder Surfaces<\/h3>\n\n

Well-formed solder joints on flat pads have a characteristic mirror-like flat top surface. Coaxial illumination \u2014 where the light is directed along the optical axis of the camera \u2014 produces a bright, uniform reflection from this flat surface. Defective joints with a rough, irregular, or tilted surface reflect less light back along the optical axis and appear darker. This brightness difference is the basis for coaxial solder joint inspection.<\/p>\n\n

Coaxial illumination is also effective for inspecting gold-plated pads before soldering. The gold surface is highly specular. Under coaxial illumination, gold pads appear uniformly bright. Contamination, oxidation, or damage on the pad surface disrupts the specular reflection and appears as a darker region. This allows pre-reflow pad inspection as well as solder joint quality verification.<\/p>\n\n

Dark-Field Illumination for Solder Defect Detection<\/h3>\n\n

Darkfield illumination at low angles is effective for detecting solder bridges, solder balls, and surface contamination on PCBs. Under grazing-incidence illumination, the flat solder mask and flat pad surfaces appear dark. Raised solder features \u2014 bridges between pads, solder balls on the board surface, lifted component leads \u2014 scatter light and appear bright. This contrast makes small solder defects visible even when they are only a fraction of a millimetre in height.<\/p>\n\n

Component Placement Verification: Backlight and Ring Illumination<\/h2>\n\n

Component placement verification checks that components are present, correctly oriented, and within placement tolerance. Different component types require different illumination approaches.<\/p>\n\n

Backlight f\u00fcr die Konturinspektion bedrahteter Bauteile<\/h3>\n\n

For leaded through-hole components and large SMT packages with visible lead outlines, backlight illumination provides the highest contrast for lead position and bend measurement. The component leads appear as dark silhouettes against the bright backlight. Coplanarity of leads, lead spacing, and presence of bent or missing leads are all measurable from the silhouette image with sub-pixel accuracy.<\/p>\n\n

Ring Illumination for Component Presence and Polarity<\/h3>\n\n

Ring illuminators provide front illumination that is well suited for component presence detection and polarity marking reading. The ring geometry illuminates the top surface of the component from all azimuths, producing a uniform bright-field image of the component body. Component markings, polarity indicators, and orientation features are visible against the component body background. This is the standard approach for verifying correct orientation of diodes, electrolytic capacitors, and polarised ICs.<\/p>\n\n

Trace and Via Inspection on Bare Boards<\/h2>\n\n

Bare board inspection checks copper trace continuity, trace width, trace spacing, and via presence before components are mounted. The inspection target is the copper trace pattern on the solder mask surface.<\/p>\n\n

Coaxial or near-coaxial direct illumination is the standard approach for bare board inspection. The solder mask surface has a defined reflectance. The copper trace areas have a different reflectance. The contrast between the two allows the trace pattern to be imaged clearly. For high-density boards with very fine trace widths below 100 micrometres, NIR illumination can improve the contrast between copper and solder mask by exploiting the different spectral reflectance of the two materials.<\/p>\n\n

Via Inspection<\/h3>\n\n

Via holes on a bare board appear as dark circles against the bright surrounding copper or solder mask under coaxial illumination. The via diameter, spacing, and fill status are measurable from the image. Unfilled vias that should have been plated appear different from properly filled vias. Backlight illumination can also be used for via inspection when the board is thin enough for light transmission.<\/p>\n\n

IC Marking and Serialisation Reading<\/h2>\n\n

IC marking verification and datamatrix or barcode reading on component packages are common tasks in electronics inspection. The marking is typically laser-etched or ink-printed on a plastic or ceramic package body. The contrast between the marking and the package surface depends on the marking type, package colour, and illumination conditions.<\/p>\n\n

For laser-etched markings on dark IC packages, low-angle direct illumination enhances the height difference between the etched and unetched surface, producing better contrast than front-facing illumination. For ink-printed markings on plastic packages, direct front illumination at a moderate angle is usually sufficient. For data matrix codes that must be read reliably at high speed, a combination of adequate intensity and correct angle is more important than the specific illuminator geometry.<\/p>\n\n

Handling Reflective Gold and Tin Surfaces Without Glare<\/h2>\n\n

Gold-plated connectors, tin-coated leads, and solder-wetted surfaces are among the most challenging materials in PCB inspection because of their very high specular reflectance. Under direct front illumination, these surfaces produce intense specular hotspots that saturate the camera sensor and make it impossible to see the features of interest.<\/p>\n\n

Three approaches are used to manage specular reflections from gold and tin surfaces.<\/p>\n\n

The first is coaxial illumination, which uses the specular reflection constructively by aligning the reflection with the camera axis. Features that are flat and perpendicular to the optical axis appear uniformly bright. Features that are tilted or irregular appear darker.<\/p>\n\n

The second is dome or flat dome illumination, which fills the hemisphere of illumination angles so that specular reflections are spread over the entire dome interior rather than concentrated at a single angle. This eliminates bright hotspots at the cost of some reduction in feature contrast.<\/p>\n\n

The third is polarisation. A polarising filter on the illuminator and a cross-polarised analyser on the camera lens eliminates specular reflections from metallic surfaces. Only the diffusely scattered component of the reflected light passes through the cross-polarised analyser. This completely removes glare from gold and tin surfaces and reveals surface features that are masked by the specular reflection under unpolarised illumination.<\/p>\n\n

<\/div>\n\n

Produkte und Technologien<\/h2>\n\n
<\/div>\n\n

RODER Vision Illuminator Families for PCB and Electronics Inspection<\/h2>\n\n

The following RODER Vision product families address the most common illumination requirements in PCB assembly inspection and electronics quality control.<\/p>\n\n

\n
\n
\"RODER<\/a><\/figure>\n\n\n

DC6 \u2014 Hochdichter LED-Ring<\/a><\/h4>\n\n\n

Ring illumination for component presence, polarity marking, solder joint inspection. Near-coaxial geometry for reflective pad surfaces. Multi-wavelength.<\/p>\n<\/div>\n\n\n

\n
\"RODER<\/a><\/figure>\n\n\n

FD2 \u2014 Flat-Dome-LED-Beleuchtungen<\/a><\/h4>\n\n\n

Diffuse illumination for assembled PCBs with mixed reflective and matt surfaces. Eliminates specular hotspots. Ideal for full-board presence and cosmetic checks.<\/p>\n<\/div>\n\n\n

\n
\"RODER<\/a><\/figure>\n\n\n

DL6 \u2014 Hochdichte LED-Matrix<\/a><\/h4>\n\n\n

Direct matrix illumination for bare board trace inspection, IC marking reading, and datamatrix verification. HTTM thermal stability. NIR and UV options.<\/p>\n<\/div>\n\n\n

\n
\"BL3<\/a><\/figure>\n\n\n

BL3 \u2014 LED-Backlight-Serie<\/a><\/h4>\n\n\n

Backlight for leaded component silhouette inspection: lead coplanarity, spacing, and bend detection. High uniformity. Multiple sizes and wavelengths.<\/p>\n<\/div>\n<\/div>\n\n

<\/div>\n\n

H\u00e4ufig gestellte Fragen<\/h2>\n\n
<\/div>\n\n
What illumination technique is best for solder joint inspection on PCBs?<\/strong>

Coaxial illumination is the most effective technique for inspecting flat solder pad surfaces and gold-plated pads. It produces a bright, uniform reflection from flat surfaces and reveals defects as darker regions. Darkfield illumination at low angles is effective for detecting raised solder defects such as bridges, solder balls, and lifted leads, which appear bright against the dark background.<\/p><\/div>

How do I inspect reflective gold-plated surfaces without glare?<\/strong>

Three approaches are used: coaxial illumination, which uses the specular reflection constructively; dome or flat dome illumination, which spreads reflections across the entire hemisphere to eliminate hotspots; and cross-polarised illumination, which removes specular reflections entirely by using a polarising filter on the illuminator and a cross-polarised analyser on the camera lens. Cross-polarisation is the most complete solution for eliminating glare from gold and tin surfaces.<\/p><\/div>

Welche Wellenl\u00e4nge sollte f\u00fcr die PCB-Leiterbahninspektion verwendet werden?<\/strong>

NIR wavelengths (850 nm or 940 nm) can improve contrast between copper traces and solder mask on bare boards by exploiting the different spectral reflectance of the two materials. UV illumination can enhance the contrast of certain solder mask colours and reveal contamination on pad surfaces. For general PCB inspection, red (617 nm) or white illumination is used as a starting point, with NIR or UV considered for applications where standard visible wavelengths do not provide sufficient contrast.<\/p><\/div>

Can I use the same illuminator for multiple PCB inspection tasks?<\/strong>

In most cases, different inspection tasks on the same PCB require different illumination geometries. A single camera station may use a ring illuminator for component presence and a flat dome for assembled board cosmetic inspection, triggered separately for each task. For high-throughput inline AOI systems, multiple illumination modes are triggered in sequence to acquire separate images for each task at full production speed.<\/p><\/div>

What illumination is needed for datamatrix and barcode reading on IC packages?<\/strong>

For laser-etched datamatrix codes on dark IC packages, low-angle direct illumination enhances the height difference between etched and unetched areas, improving contrast. For ink-printed codes, front-facing direct illumination at a moderate angle is usually sufficient. Adequate intensity and correct angle are more important than the specific illuminator geometry. Strobe mode ensures sufficient intensity without thermal degradation of the illuminator.<\/p><\/div><\/div>\n\n